GD Satcom ModuMAX 1500 Watt Modular C-Band SSPA
- Built-in redundancy
- RF plug-in modules
- Easy to operate and maintain
- Phase-combined systems
GD Satcom ModuMAX Features
- True High-Power HOT-SWAP Modular System
- Switchless redundancy
- No switching, no external hot standby required
- Configurable Power Levels
- N+X redundancy in a single system
- Configure operating RF power level as required for application and mission
- Extremely Low MTTR
- Less than 3 minutes for module replacement
- Full Diagnostics
- Intelligent, Ultra-High Efficiency Power Supply System
- Single Module Failure Compensation Feature
GD Satcom ModuMAX 1500 Watt C-Band SSPA
GD Satcom C-Band ModuMAX (Indoor), 1.5kW SSPA, 5.85-6.425 GHz, 1384W @ P1dB. Completely modular solid-state power amplifier systems for world-wide satellite communications.
Satellite communications providers face significant risk when the link to a satellite is disrupted. Critical applications go offline, customers lose confidence, and revenue is lost as providers scramble to recover the link. Thus, most satellite earth stations employ brute-force redundancy, i.e. two of everything, to reduce the risk, but at significant cost and increased complexity. When the final amplifier stage was a single tube and thus a single point failure, having a second amplifier immediately available was a pragmatic solution. However, with the demonstrated viability and practicality of solid-state amplifiers, non-brute-force redundancy solutions offer significant cost and performance advantages.
ModuMAX Power Options
Solid-state power amplifiers (SSPAs) consist of multiple transistors in parallel, and consequently contain built-in redundancy. Because of forward thinking design, including multiple parallel RF modules, power supplies and cooling fans, GD Satcom ModuMAX SSPAs are extremely reliable and fault-tolerant. With the ModuMAX series, one fault-tolerant SSPA can replace two conventionally designed high power amplifiers yielding significant installation savings and reduced operating costs.
A ModuMAX SSPA combines the RF output power from eight identical, fully interchangeable RF plug-in modules (16 in a phase-combined system) to obtain the rated power capacity. These amplifier modules can be individually turned on or off via either local or remote control. Installations can exploit this feature of the ModuMAX SSPA to reduce prime power consumption during times when the required RF output power is lower than the maximum linear power capacity of the amplifier.
Additionally, the amplifier modules can also be employed in a redundancy configuration where, in the event of a fault occurring in the online modules, spare modules can be brought on line rapidly via M&C. Configurable power, the ability to adjust the number of enabled modules to match the system output power requirements or configure the modules in a redundant array, is a key feature of the ModuMAX design.
Configurable power is implemented by determining the minimum number of modules that must be enabled to provide the required RF output power. To use configurable power, determine how many RF modules must be on line to meet the required power while leaving the remaining modules offline. Any modules not needed to support the system traffic load are deactivated, either locally or via one of the remote interfaces. When the system is operating, the remote M&C system monitors the ModuMAX for faults. If the M&C system detects a fault in an enabled amplifier module, it immediately enables one of the deactivated modules to compensate for the loss. No minimum warmup time is required; the amplifier modules become functional immediately upon enabling.
Configurable power allows prime power consumption to be significantly reduced by deactivating modules while still meeting the system RF power requirements. While power consumption is approximately proportional to the number of enabled modules, RF output capacity decays as shown in Table 1.
ModuMAX SSPAs can also be phase-combined in a single rack utilizing a fixed (hybrid) or variable (VPC) phase combining system. The VPC system affords the operator the flexibility to configure the system for operation using either ModuMAX SSPA individually (single mode), or using both simultaneously (phase-combined mode) to nearly double the system output power. A ModuMAX system based on a VPC has a total of 16 RF modules (8 in each of 2 RF units), together with power supplies and the VPC sub-system contained in a single rack.
RF Plug-In Modules
The RF plug-in modules are conveniently accessible from the front panel. Summary module status is visually indicated by a multicolor indicator on each module with detailed information available at the control panel display.
Failure of a single module causes a drop of approximately 1.2 dB in output power—without the momentary loss of signal caused by redundant switchover systems (Table 1). Defective RF modules can be hot-swapped while the SSPA continues to operate. Since they contain only a fraction of the RF power transistors in the SSPA, spare RF modules are affordable.
Easy to Operate and Maintain
ModuMAX SSPAs are designed to be easy to operate and maintain. All features can be fully remote controlled through standard RS-232/-422/-485 and network interfaces. For quick and easy manual access, the most commonly used controls are located on the front panel.
Most maintenance can be performed safely while the SSPA continues to operate. Any of the eight fans in the aircooling system can be easily removed and replaced, without ever taking the SSPA off-line. Even the power supply modules are redundant and hot swappable.
A ModuMAX system is easily expandable. Phase-combine two SSPAs for double the power output using only 61.25" (35 RU) of rack space (High power systems with two PS chassis per RF unit require 71.75" [41 RU]). With 16 phase combined RF modules, one failed module causes only about 0.6 dB drop in output power.
Global EMC and Safety Compatibility
ModuMAX SSPA systems are certified to applicable EU EMI/EMC and safety standards.
ModuMAX also incorporates redundancy into its integral forced-air cooling system. Sufficient cooling margin is built into the design to tolerate the loss of one cooling fan. Fans are monitored for rotational speed, and failure of a fan is indicated on the control panel display. In the event of a fan failure, the SSPA can continue to operate until a replacement is installed. The air cooling system utilizes separate rear panel air intake and exhaust ducts and can be vented either outdoors or into the room.
For most systems, operating power is supplied by three identical plug-in power supply modules in a rack-mount chassis; higher output systems require six modules (two PS chassis) per RF unit for full redundancy. If a module fails, the remaining ones can supply 100% of the required load current and the defective module can be hot-swapped without interruption.
ModuMAX SSPAs can be connected to 120/208 Vac or 230/400 Vac three-phase sources, or to single-phase 180–264 Vac, supporting installation worldwide.
|C-Band ModuMAX Technical Specifications|
| Frequency Range|
5.850 - 6.425 GHz
5.850 - 6.725 GHz
|Gain, at Maximum Setting||70 - 75 dB|
| Gain vs. Temperature (0 to 50 °C) |
|Gain Adjust Range Digital, 0.1 dB steps||20 dB|
| Gain Flatness|
per 40 Mhz
| Saturated Power Output|
+62.0 (1585) dBm (W)
+60.0 (1000) dBm (W)
+59.0 (800) dBm (W)
| Power Output, at 1 dB Compression (P1 dB)|
+61.3 (1384) dBm (W) min
+59.5 (900) dBm (W) min
+58.5 (708) dBm (W) min
|Two-Tone Intermodulation At 3 dB backoff from P1 dB||-25 dBc max|
| Residual Noise |
-70 dBW/4 kHz
-160 dBW/4 kHz
| Group Delay|
1.0 ns p-p
|AM/PM Conversion At P1 dB|| 2.5°/dB typ.|
|Second Harmonic At P1 dB||-60 dBc|
|Spurious at P1 dB||-70 dBc|
|VSWR Input, Output||1.3:1 max|
|Sample Ports Input/Output||-10/-50 dBc|
|Power Requirements||8.3 kW max (Cold start at 0 °C and saturated output.)|
| Cooling System |
Rear panel ducts
Volumetric air flow
400 cfm (0.189 m3/s)
|Operating Temperature (Ambient/inlet air)||0 to +50°C|
|Altitude Derating 10,000 ft (3000 m) max.||Derate 2°C per 1000 ft (300 m)|
RF Unit (13 U panel ht.)
Power Supply (4 U ht.)
19.0 W x 22.72 H x 27.38 D inches
483 W x 577 H x 695 D mm
19.0 W x 6.97 H x 22 D inches
483 W x 177 H x 559 D
253 (115) lb (kg)
88 (40) lb (kg)